Flow Production Transporters

move Your Products to be assembled from Station to Station


Below you will find a big choice of different Flow Production Transporters with which you can move your products to be assembled through your flow production line, from assembly station  to assembly station. Such products for example can be big and heavy gearboxes, harvesters, mining trucks up to nacelles for wind energy systems.

The choice of products indicated below for sure will not be complete. There are much too much individual possibilities for organizing a flow production line. The indicated choice of Flow Production Transporters however gives a good overview about our options.

Our Flow Production Transporters preferably are freely manoeuvrable battery-driven carts, which do not need any kind of rails for running or to be guided. By this way you always will be able to adopt the traffic routing of your Flow Production Line to your actual need, at any time, without time-intensive and expensive work on the floor for modifying the routing of rails and others. 


Please introduce to us your Flow Production Project. We would like to present to you without obligation an offer for suitable Flow Production Transporters.

Please contact us by phone or email. We would like to counsel you.
 

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de



 

Flow Production Transporter for Harvesters

pulls Harvesters up to 32 tons from Assembly Station to Assembly Station


Self-propelled harvesters more and more are produced according to the Flow Production Principle. This means that they have to be driven through a different number  of assembly stations, specific to the single model.

As self-propelled harvesters will be able to leave the production line after finalisation of assembly at the last station earliest, they are pulled through the Flow Production Assembly Line, from assembly station to assembly station, by Flow Production Transporters
Usually the Flow Production Transporter drives below of the harvester and either lifts the chassis of the harvester directly below the front or rear axle or via an adaptor fixed to the chassis of the harvester. At its opposite end the harvester is rolling on its own wheels.  
 
The Flow Production Cart shown here is controlled via a radio control. By this way the operator always can choose the position which gives to him the optimal visibility of the workplace.

This electrically driven Pulling Cart is suitable for all kinds of self-propelled harvesters, for example for beet harvesters, potato harvesters, corn harvesters, combine harvesters and a lot of others. 

Do You intend to reorganize your production of self-propelled harvesters to install the Flow Production Principle? Verymuch we would like to counsel you.

Please contact us by phone or email.

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de


 

Flow Production Transporters for Special Trucks

moves heavy Mining Trucks during their Assembly


Mining trucks as well as a lot of other special trucks also are produced according to the Flow Production Principle.
Hereby very often the complete truck needs to be lifted.
The Flow Production Transporter shown on above photos consists of a Push- / Pull Unit and a trailer axle with integrated hydraulic lift. 

The front part of the Flow Production Transporter itself consists of a Push- / Pull Unit with flanged load unit including hydraulics. THis is a very reasonably priced way of construction. The operator can move the Flow Production Cart either via the handle, or, if this is more recommendable by reason of available space, by the attached cable remote control.

For further information on this Flow Production Transporter please contact us by phone or email. We very much would like to counsel you. 
 

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de


 

Flow Production Transporter for Truck Assembly

moves Your Truck through the Assembly Line safely


Special trucks like dumpers and a lot of other trucks also are produced according to the Flow Production Principle.
Hereby the truck to be assembled will be lifted by the Flow Production Transporter either at one end or at both ends of truck.

The Flow Production Transporter shown on the photos above consists of a push- / pull unit and a corresponding hydraulically operated load pick up. Optionally for the opposite end of the special truck to be pulled there is available a trailer axle with integrated hydraulics. The operator can steer this Flow Production Transporter either by the handle or, if this is more recommendable by space reasons, by cable-connected remote control.      

For more information regarding this Flow Production Transporter please contact us by phone or email. We very much would like to counsel you.

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de

Flow Production Transporter for big Components / Machines

moves all Types of Big Components positioned on Pallets / Assembly Stands to be crossed below


Beside of trucks and carts a lot of other products also is produced following the flow production principle. This for example can be big components like motors, gearboxes, nacelles for wind energy systems, specail machinery and a lot more of products.
These components very often are assembled on assembly stands which look like a big steel pallet and can be crossed below and lifted up by a suitable Flatbed Truck.

These Flow Production Flatbed Trucks cross below the steel pallet / assembly stand completely and lift it up from the bottom side as much as necessary to move it within the production building. By this way the Big Components to be assembled are moved from one assembly station to the next.  

Using the Flatbed Trucks as freely manoeuvrable Flow Production Transport Carts for carrying the assembly stands / pallets, you as the customer can adopt the routing of your Flow Production Line to the newest requirement at any time. You can add assembly stations or leave away assembly stations, change the flow of the line, take single production stands out of the line flow and put them in again later. There will be no need to do any expensive work on the floor for changing the routing of rails or similar things. You can modify the routing of your Flow Production Line immediately at any time, and this at lowest possible cost.

Weights of the big components to be assembled of 150 tons or more are not unusual.

For more information regarding this Flow Production Transporter please do contact us by phone or email. We very much would like to counsel you.  

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de

 

   

Flow Production Transporters for extremely long Products

Moves Your Long Product / Your Long Component around any Corner


Within a lot of industry sectors there are products produced which are very long and which need to be moved through several assembly stations during their production. On this way it may happen that they need to be moved sidewards one or several times. It also may be possible that they need to be driven around very narrow corners with an angle of 90° or even up to 180°. This procedure may be needed for very long shafts or spindles of several meters length or within production of big and heavy "Long Products" like for example escalators.

On the photos above you can see our "Long Product Movers" how they are used at industrial production.
For driving lengthwise usually one Push- / Pull Unit PTT3 with a hooked up front end mover at the front end of the product / total construction will be sufficient. At the rear end there is the rear end mover which is steered manually by a simple handle, without any drive.

In the moment when the product is requested to be moved transversal, a second Push- / Pull Unit PTT3 will be used to hook up the rear end mover.
 
Both load trolleys, the front end mover as well as the rear end mover, are equipped with very strong load wheels and can be turnded by the Push- / Pull Units PTT3 on the spot. Therefore it also is possible to turn the complete long product on the spot. 

For further information please contact us by phone or email. We very much would like to counsel you.

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de 


 

Flow Production Transporters for Movement of Skids

moves Your Skids from Station to Station safely


At flow production lines very often there are installed special station, at which for example very big and heavy components of a lot of tons of weight need to be turned. It is necessary to turn these components, because for example before reaching this station the big component had been equipped with a lot of parts from above. Now there are parts to be fixed to the big component from the lower side. As these parts to be fixed can be heavy and also for safety reason it is not recommendable to stand below the big and heavy component for assembly work. 

The big components usually are driven into the turning station and also driven out of the turning station by transport trolleys, so called "Skid". Skids usually are rolling on rails, but also can be freely steerable.
For moving of such skids usually Push- / Pull Units PTT3 are used. They are driven to the corresponding skid and are connected to the skid by their quick coupling within seconds. Immediately the skid can be pulled or pushed. Very often such a Push- /Pull Unit PTT3 can be used at a lot of different skids.  

For more information regarding the use of the Push- / Pull Unit PTT3 as a Flow Production Transporter for moving of skids please contact us by phone or email. We very much would like to counsel you. 

Tel.: 0049 2156 419193
Fax: 0049 2156 4979325
eMail: info@seidel-handlingsysteme.de 


 

heavy load indoor universal truck type 1 high_lift_coil_transport_carts_with_carrying_bolt_and_change_prism feeder straighteners TAL100 9150 Handlingsysteme truck_for_coil_transport vehicles_for_coil_transport Coilhandling Die Handling / Die Change Transformatorenfertigung indoor_heavy_load_pallet_transport_carts conventional line for coil feeding Schwerlasthandling push_pull_unit_PTT3_with_lifting_hydraulics pedestrian_transport_solutions_PTT3